Frequently Asked Questions (FAQ): KAISE KT-2011 Digital Multimeter:

1/ What is the KAISE KT-2011 digital multimeter and who is it designed for?

The KT-2011 is a handheld, high-performance digital multimeter offering up to 500,000 counts. It’s engineered for electronics technicians, field service engineers, and laboratory users who need precise measurements and data-logging capabilities.

2/ What measurement functions and ranges does the KT-2011 support?

The KT-2011 covers all standard multimeter functions.

• DC voltage: 500 mV, 5 V, 50 V, 500 V, 1000 V

• AC voltage: 500 mV, 5 V, 50 V, 500 V, 1000 V

• DC current: 500 µA, 5000 µA, 50 mA, 500 mA, 5 A, 10 A

• AC current: 500 µA, 5000 µA, 50 mA, 500 mA, 5 A, 10 A

• Resistance: 500 Ω, 5 kΩ, 50 kΩ, 500 kΩ, 5 MΩ, 50 MΩ

• Continuity test with buzzer

• Diode test

• Frequency measurement up to 999,999 Hz

3/ How accurate is the KT-2011 when measuring DC voltage?

The DC voltage accuracy is 0.03% of reading, making it suitable for demanding calibration tasks and precision electronics work.

4/ How is the KT-2011 powered and what is its expected battery life?

It uses a single 9 V battery (6F22/006P). Under typical lab or field use, you can expect 100–150 hours of continuous operation before the low-battery indicator appears.

5/ How do I turn the meter on/off and select a measurement mode?

• Turn the rotary selector to your desired function (e.g., DCV, Ω, DCA).

• To power off, rotate the selector fully to “OFF.”

• Always start in a higher range if you’re unsure of the signal magnitude.

6/ How should I connect the test leads?

• Insert the black lead into the COM socket.

• For voltage, resistance, frequency, and diode: insert the red lead into the V/Ω/Hz socket.

• For current measurements up to 500 mA: use the mA socket; for up to 10 A: use the 10 A socket.

7/ How do I measure DC voltage?

• Set the selector to DCV.

• Connect black probe to the negative terminal, red probe to the positive terminal.

• Read the value on the display.

• If “OL” appears, switch to a higher range.

8/ How do I measure AC voltage?

• Set the selector to ACV.

• Connect probes as you would for DC.

• Observe the waveform stability on the bar graph for best accuracy.

9/ How do I measure DC and AC current?

• Choose the correct current socket (mA or 10 A).

• Set the selector to DCA (DC current) or ACA (AC current).

• Break the circuit and connect the meter in series.

• Reverse polarity if the reading shows negative when measuring DC.

10/ How do I measure resistance and test continuity?

• Set the selector to Ω.

• Place probes across the component or circuit.

• A reading near zero indicates continuity; a buzzer will sound if resistance is very low.

11/ How do I use the Max/Min recording function?

• Press the Max/Min button once to enter recording mode.

• The display toggles through maximum, minimum, ΔMax-Min, and live readings.

• Press again to exit back to normal measurement.

12/ What is the bar-graph indicator and how is it useful?

• The 60-segment bar graph updates at 60 Hz.

• It visually tracks rapid signal changes that numbers alone might miss.

13/ How do I change the sampling rate?

• Press the SAMPLE button to toggle between 50,000 samples per second and 500,000 samples per second.

• Use the lower rate to conserve battery life when you don’t need ultra-fast capture.

14/ How do I replace the battery and how is low battery indicated?

• When the battery icon appears on the LCD, open the rear battery cover.

• Replace the old 9 V battery with a fresh one, observing polarity.

• Tighten the cover to maintain safety ratings.

15/ How do I check and replace the protective fuses?

• Remove the back cover to access the fuse compartment.

• The mA range fuse is typically 250 mA/600 V; the 10 A range fuse is 11 A/1000 V.

• Replace with manufacturer-specified fuses only.

16/ What error messages might appear and how do I troubleshoot?

• “OL”: Overload – switch to a higher range or check connections.

• “Err”: Internal error – power cycle the meter; if it persists, seek authorized repair.

• Blank or flickering display: Check the battery and fuse condition.

17/ What safety precautions should I follow?

• Never exceed rated input limits.

• Do not touch metal probe tips when measuring live circuits.

• Disconnect test leads before changing settings.

• Store in a dry environment and avoid mechanical shocks.

18/ What accessories come with the KT-2011?

• Standard test leads

• Spare fuses for mA and 10 A ranges

• Holster/carrying case

• User manual

19/ What are the physical dimensions and weight?

• Dimensions: 186 mm × 87 mm × 35 mm (H×W×D)

• Weight: 390 g (excluding holster)

20/ Does the KT-2011 support PC connectivity or data logging?

• Yes, it features a PC-link function for downloading readings to a computer.

• Requires optional interface cable and dedicated software.

21/ What warranty and technical support are available?

• Typically covered by a 12-month manufacturer’s warranty.

• Please contact QTE Technologies (qtetech.com/en).